Electronics

SPDT through-hole slide switch

Used on Hyper-pi to pull the PowerBoost enable pin low without carrying the full load current.

Used in: Hyper-pi

Flexible stranded copper hookup wire; gauge not specified by the creator

Choose insulation and gauge suitable for the expected current; Hyper-pi's source does not give an exact size.

Used in: Hyper-pi, DC34 A7S Cyberdeck, FrameDeck, HandiPi, Paper Pi Handheld

Momentary through-hole tactile switch, 6mm body

Exact manufacturer and actuator height are not stated.

Used in: Little Luggable, DC34 A7S Cyberdeck, Chonky Palmtop, Paper Pi Handheld

Axial small-signal switching diode

The source calls for 64.

Used in: Little Luggable, Penkesu Computer, PiMech Deck, Chonky Palmtop, Rasti Computer, CyberKeeb 2040

Panel-mount latching push button, 12mm body

Contact rating and pole configuration are not stated.

Used in: Little Luggable

5V/16MHz ATmega32U4 microcontroller board

Penkesu specifies one Pro Micro; PiMech says any Pro Micro-compatible board will do. Check voltage and USB connector before substitution.

Used in: Penkesu Computer, PiMech Deck, Chonky Palmtop, QAZ Cyberdeck, Framework Cyberdeck

Two-position SPDT slide switch

Penkesu’s wiring diagram requires a switch between PowerBoost EN and GND, but the creator does not specify a model — confirm dimensions and ratings.

Used in: Penkesu Computer

Two-position through-hole SPDT slide switch

The exact switch model linked by the PiMech BOM.

Used in: PiMech Deck

General assembly consumables; sizes and quantities not specified

The PiMech BOM calls for these supplies but gives no gauge, pitch, length or count — select them to suit the wiring and insulate every exposed joint.

Used in: PiMech Deck

Photoacoustic CO₂, temperature and humidity sensor breakout

Tinycorder lists an SCD40 sensor; use a breakout with I²C access.

Used in: Tinycorder Environmental Data Logger

AS7341 visible-light spectral sensor, I²C breakout

Tinycorder uses this sensor for light-spectrum measurements.

Used in: Tinycorder Environmental Data Logger

BMP280 I²C/SPI breakout

Tinycorder BOM specifies a BMP280 sensor.

Used in: Tinycorder Environmental Data Logger

Small through-hole perfboard, 8 by 12 holes

Tinycorder uses this as the internal carrier board; trim-to-size board may be substituted.

Used in: Tinycorder Environmental Data Logger, RadioDeck GQRX Hardware Console

Custom 2-layer through-hole PCB, approximately 86 × 74mm, fabricated from the project Gerbers

Upload the official fabrication archive from the source repository to a PCB manufacturer; this entry is for the bare board only.

Used in: DC34 A7S Cyberdeck

Compact RP2040 microcontroller board with castellated pads

The exact input-controller module named in the shield BOM; confirm the assumed 15.24mm row spacing before PCB fabrication.

Used in: DC34 A7S Cyberdeck

Approximately 0.1µF radial ceramic capacitor for 3.3V radio-rail decoupling

The shield BOM specifies an approximate value and suggests adding 1–10µF if needed; confirm against radio-module behavior.

Used in: DC34 A7S Cyberdeck, RadioDeck GQRX Hardware Console

Radial PPTC resettable fuse, approximately 0.5A hold current

The creator calls the rating approximate and requires confirmation against radio current draw.

Used in: DC34 A7S Cyberdeck

Assorted small-diameter heat-shrink tubing for insulated off-board wiring

The source calls for heat-shrink as needed and does not specify sizes or shrink ratio.

Used in: DC34 A7S Cyberdeck

Bidirectional logic-level converter suitable for the Pico-to-LCD I2C bus

The source does not identify a manufacturer or exact channel count; confirm I2C compatibility.

Used in: RadioDeck GQRX Hardware Console

10kΩ axial resistor for the RadioDeck rotary-switch ladder

The source specifies resistance but not tolerance or wattage.

Used in: RadioDeck GQRX Hardware Console

100kΩ axial resistor used as a pull-down

The source specifies resistance but not tolerance or wattage.

Used in: RadioDeck GQRX Hardware Console

2.54mm-pitch short female machine-pin socket strips

One of the two exact Adafruit socket/header products linked for the Chonky Palmtop keyboard controller.

Used in: Chonky Palmtop

2.54mm-pitch short male machine-pin header strips

One of the two exact Adafruit socket/header products linked for the Chonky Palmtop keyboard controller.

Used in: Chonky Palmtop

Creator-designed USB-mode, power and display-level adapter board

Fabricate from the official repository design files. The source names TUSB320, SN74LVC8T245, MCP1640 and two TPS22917 load switches.

Used in: Modem Thing

One enclosed speaker set connected to the Framework mainboard

Creator BOM links Adafruit product 1669.

Used in: FrameDeck

Momentary PCB switch, 6×6mm body, 7mm height, four through-hole pins

Keyboard-controller reset switch; manufacturer and force are unspecified.

Used in: FrameDeck

Surface-mount small-signal switching diode in SOD-123 package

HandiPi keyboard BOM requires 36; exact manufacturer is not stated.

Used in: FrameDeck

Low-profile momentary keyboard switch; exact variant unspecified

Used for the mainboard power control; verify footprint and actuation before ordering.

Used in: FrameDeck

16mm panel-mount momentary PC power switch

Creator links an example listing; verify contact action and fit before ordering.

Used in: Rasti Computer

Breakout shim for Framework mainboard power-button connections

Exact community-made board linked by the creator.

Used in: Rasti Computer

Flexible female-to-male Dupont-style jumper wires

Exact Adafruit product linked in the PX-88 BOM; four low-profile extensions serve the display and additional wires serve the switch and LED.

Used in: Typeframe PX-88

Two-pin momentary SPST KCD3-format rocker switch

The creator says the original linked listing no longer offers the required momentary version; verify momentary action before ordering.

Used in: Typeframe PX-88

Approximately 150 ohms; through-hole form is convenient for the status LED lead

The PX-88 BOM specifies approximately 150 ohms but not tolerance or power rating.

Used in: Typeframe PX-88

5mm green through-hole LED

Exact Adafruit product linked in the PX-88 BOM for the status indicator.

Used in: Typeframe PX-88

Momentary tactile switch, approximately 6mm square, surface mount

Paper Pi README states the package and feel but not a manufacturer, actuator height or part number.

Used in: Paper Pi Handheld

General-purpose prototyping board; dimensions and pitch not stated

Paper Pi keyboard list names small perfboards without dimensions or a part number.

Used in: Paper Pi Handheld

Small-signal diode; model and quantity not stated

Paper Pi keyboard matrix uses signal diodes, but the creator does not give a part number.

Used in: Paper Pi Handheld

Six-pin slide switch; electrical ratings and manufacturer not stated

Part designation is transcribed from the Paper Pi README; confirm footprint and switching configuration.

Used in: Paper Pi Handheld

10kΩ pull-up resistor; package, tolerance and wattage not stated

Paper Pi GPIO controls use external 10kΩ pull-ups.

Used in: Paper Pi Handheld

Five-position female through-hole header; pitch not stated by the creator

CyberKeeb 2040 V2 specifies two, but does not state pitch or exact model.

Used in: CyberKeeb 2040

Four-position through-hole DIP switch

CyberKeeb 2040 uses it to disconnect the four SPI lines; the exact package is not specified.

Used in: CyberKeeb 2040

PCB-mounted slide switch; exact package and ratings not stated

The V2 BOM names one slide switch for Pi power but does not identify a model.

Used in: CyberKeeb 2040

10nF ceramic capacitor, 1206 SMD package; voltage and tolerance not stated

CyberKeeb 2040 V2 specifies two; confirm dielectric, tolerance and voltage for substitution.

Used in: CyberKeeb 2040

330-ohm axial through-hole resistor; wattage and tolerance not stated

CyberKeeb 2040 V2 specifies one; confirm lead spacing and rating before ordering.

Used in: CyberKeeb 2040

10-kilohm axial through-hole resistor; wattage and tolerance not stated

CyberKeeb 2040 V2 specifies four; confirm lead spacing and rating before ordering.

Used in: CyberKeeb 2040

40-pin dual-row header; pitch and height not stated by the creator

CyberKeeb 2040 V2 uses one to join the Pi Zero to the keyboard PCB.

Used in: CyberKeeb 2040

RP2040 microcontroller development board

CyberKeeb 2040 V2 uses a Pico running PicoMK as the keyboard controller.

Used in: CyberKeeb 2040

Passive five-port JST-SH I2C hub

Exact Adafruit product linked in the vecdec v1.1 bill of materials.

Used in: vecdec 1.1

ATmega32U4 Pro Micro-compatible keyboard controller with USB-C

The vecdec source recommends Elite-C for fit and notes that alternatives may require STL modification.

Used in: vecdec 1.1

Creator Gerbers for one 1.6mm keyboard circuit PCB and one 1mm keyboard cover PCB.

Fabricate from the official repository files; the creator BOM does not name a board house.

Used in: HandiPi

Surface-mount switching diode used in the HandiPi keyboard matrix.

Source BOM specifies 1N4148 in SOD-123; this linked 1N4148W uses that package.

Used in: HandiPi

ATmega328 family, DIP package; precise suffix not specified.

Do not order until the precise compatible device and firmware programming requirements are confirmed against the creator files.

Used in: HandiPi

16 MHz; package and load capacitance are not specified by the creator.

Confirm package, lead spacing, tolerance, and load capacitance against the keyboard PCB before ordering.

Used in: HandiPi

Through-hole ceramic load capacitor for the keyboard-controller crystal.

Creator BOM gives capacitance but no voltage, tolerance, or lead spacing; confirm against the PCB before purchase.

Used in: HandiPi

General-purpose 10 kΩ through-hole resistor used by the HandiPi electronics.

Creator BOM gives resistance only; confirm wattage, tolerance, and quantity from the PCB files.

Used in: HandiPi

100 nF ceramic capacitor; exact voltage, dielectric, and package are not specified by the creator.

HandiPi BOM requires two. Confirm package and rating against the keyboard PCB before ordering. Source: https://github.com/brickbots/HandiPi/blob/main/docs/BOM.md

Used in: HandiPi

4.7 µF electrolytic capacitor; exact voltage and package are not specified by the creator.

HandiPi BOM requires one. Confirm polarity, voltage, and lead spacing against the PCB. Source: https://github.com/brickbots/HandiPi/blob/main/docs/BOM.md

Used in: HandiPi

3.6 V Zener diode; exact manufacturer part number and package are not specified by the creator.

HandiPi BOM requires two. Confirm package and power rating against the PCB. Source: https://github.com/brickbots/HandiPi/blob/main/docs/BOM.md

Used in: HandiPi

75 Ω axial resistor; exact tolerance and wattage are not specified by the creator.

HandiPi BOM requires two. Confirm lead spacing and rating against the PCB. Source: https://github.com/brickbots/HandiPi/blob/main/docs/BOM.md

Used in: HandiPi

1.5 kΩ axial resistor; exact tolerance and wattage are not specified by the creator.

HandiPi BOM requires one. Confirm lead spacing and rating against the PCB. Source: https://github.com/brickbots/HandiPi/blob/main/docs/BOM.md

Used in: HandiPi

SPST slide switch; the creator links an example but does not state a manufacturer part number.

HandiPi BOM requires one. Match footprint and actuator dimensions before ordering. Source: https://github.com/brickbots/HandiPi/blob/main/docs/BOM.md

Used in: HandiPi

PCB-mount USB port; connector subtype and manufacturer part number are not specified in the creator BOM.

HandiPi BOM requires two. Inspect the PCB files before ordering. Source: https://github.com/brickbots/HandiPi/blob/main/docs/BOM.md

Used in: HandiPi

Compact pair for an enclosed portable computer

Mu Cyberdeck source names two speakers but does not state model, impedance or power rating.

Used in: Mu Cyberdeck

Low-voltage two-channel amplifier module

Mu Cyberdeck source calls for an amplifier board without identifying the chipset or rating.

Used in: Mu Cyberdeck

Panel switch for the deck power circuit; style and ratings not stated

Lambda Cyberdeck 910 requires an on/off button or switch but does not identify a model, cutout size or electrical rating.

Used in: Lambda Cyberdeck 910, Framework Cyberdeck

Two compact 8-ohm, 5-watt speakers

The Lambda Cyberdeck 910 essential-parts list names Waveshare 8Ω 5W speakers.

Used in: Lambda Cyberdeck 910

28AWG insulated stranded wire for custom USB and battery leads

The QAZ Cyberdeck creator explicitly specifies 28AWG and recommends extra length for rework.

Used in: QAZ Cyberdeck

8-ohm, 1-watt miniature speaker with two-pin 1.25mm-pitch lead

The cYbErDeCk BOM says this speaker and lead are supplied with the Waveshare board. The replacement links are only for a missing or damaged included speaker; verify dimensions and polarity.

Used in: ESP32-S3 RLCD cYbErDeCk

Replacement left/right speaker modules for a Framework Laptop mainboard

Framework Cyberdeck creator names speakers from the Framework marketplace without stating generation or speaker-kit revision. No trusted allowlisted Framework seller was found.

Used in: Framework Cyberdeck

Custom PCB fabricated from the creator-published KiCad design and Gerbers

Use the official Gerbers at the pinned source revision. Inspect the design-rule report and select fabrication options appropriate to the files.

Used in: RP2040 CyberDeck